 |
Vehicle Control Modules |
|
|
|
| Latching Relays |
| VCM-01 Alternating 12V |
| VCM-02 Alternating 24V |
|
|
|
|
 |
| Time Delay Relays |
| VCM-03 On-Delay |
| VCM-04 Off-Delay |
| VCM-05 One-Shot |
|
|
|
|
|
| Low Voltage Disconnects |
| VCM-06 (15 amp) |
| VCM-12 (20 amp) |
|
|
|
|
|
|
|
| Solid State Relays |
| VCM-10 Dual input |
|
|
|
|
|
InPower time delay relays are completely solid state and adjustable with a single +12 volt @ 15 amp output. The module has two inputs, one actuated by a transition to +12 volts (Input A) and one actuated by a transition to ground (Input B). The two inputs operate as a logical "Exclusive OR" so that either input can cause the timer to operate.
|
- Dual inputs – ground and +12 volts
- Over current protection
- Short-circuit shut down protection
|
Models include:
| VCM-03.10SA |
0 - 10 second time range |
| VCM-03.10SA |
0 - 10 second time range |
| VCM-03.60SA |
0 - 60 second time range |
| VCM-03.03MA |
0 - 3 minute time range |
| VCM-03.10MA |
0 - 10 minute time range |
| VCM-03.60MA |
0 - 60 minute time range |
The VCM-03 timer will start when +12 volts is applied to Input A while Input B is open, or when ground is applied to Input B while Input A is open. The input must be maintained to operate the timer. If removed during the timer operation (before the timer expires) the operation will reset. With the input applied, when the timer expires the output will be activated, and will remain activated until the inputs are removed. The output is rated at +12 volts @ 15 amps and provides over current and short circuit shut down protection. The time period is adjustable with a single turn potentiometer.
|
Models include:
| VCM-04.10SA |
0 - 10 second time delay |
| VCM-04.60SA |
0 - 60 second time delay |
| VCM-04.03MA |
0 - 3 minute time delay |
| VCM-04.10MA |
0 - 10 minute time delay |
| VCM-04.60MA |
0 - 60 minute time delay |
| VCM-04.05SF |
5 second fixed time delay |
| VCM-04.05MF |
5 minute fixed time delay |
The VCM-04 has two inputs, one actuated by a transition to +12 volts (Input A) and one actuated by a transition to ground (Input B). The two inputs operate as a logical "Exclusive OR" so that either input can cause the timer to operate. The output will be activated when +12 volts is applied to Input A while Input B is open, or when ground is applied to Input B while Input A is open. When the applied input has cleared, and its counterpart input is also clear, the timer will start. When the timer has expired the output will be deactivated and the operation is complete. The output is rated at +12 volts @ 15 amps and provides over current and short circuit shut down protection.
|
Models include:
| VCM-05.10SA |
0 - 10 second one-shot time delay |
| VCM-05.60SA |
0 - 60 second one-shot time delay |
| VCM-05.03MA |
0 - 3 minute one-shot time delay |
| VCM-05.10MA |
0 - 10 minute one-shot time delay |
| VCM-05.60MA |
0 - 60 minute one-shot time delay |
| VCM-05.02MF |
fixed 120 second one-shot time delay |
The VCM-05 has two inputs, one actuated by a transition to +12 volts (Input A) and one actuated by a transition to ground (Input B). The two inputs operate as a logical "Exclusive OR" so that either input can cause the timer to operate. If the module is not already in a time-out sequence, its output will be activated for the adjustable time period when +12 volts is applied to Input A while Input B is open, or when ground is applied to Input B while Input A is open. In other words, the module will not start another time sequence until both inputs are removed and the module is not in a time-out sequence. An input control signal must be applied for a minimum of 250 milliseconds, with its counterpart input open, to initiate a time-out sequence. Also, both control inputs must be removed for at least one second before another time-out sequence can be initiated. The time period is adjustable with a single turn potentiometer. The output is rated at +12 volts @ 15 amps and provides over current and short circuit shut down protection.
|
|
|
|
